Garage door spring adjustment means changing the tension on your door’s springs so they balance the weight of the door. A properly adjusted door stays put when you lift it halfway by hand, rises smoothly, and closes without slamming. If your door drifts down, creeps up, feels heavy, or makes your opener strain, the springs may need adjustment, or they may be worn out and need replacement. Spring tension work is not a DIY job. Torsion and extension springs store enough energy to cause serious injury, and DASMA, the garage door industry’s trade association, says spring replacement should only be performed by a trained door systems technician. Advanced Door is Utah’s #1 rated garage door company: family owned since 1994, 4.9 stars, 30,000+ five-star reviews, and the only company in Utah offering a lifetime warranty on parts and labor. Call (844) 971-3667 for a free estimate.

Last updated: October 2026
Most homeowners never think about their garage door springs until something feels off. Maybe the door used to glide up and now it crawls. Maybe it slams down the last foot, or it will not stay open when you lift it by hand. Maybe the opener sounds like it is working harder than it used to. All of those symptoms point to the same system: the springs that counterbalance the weight of the door.
A typical garage door is far heavier than it looks. Our guide on how much a garage door weighs explains why, but the short version is that the springs, not the opener, do almost all of the lifting. When spring tension drifts out of the right range, the door goes out of balance, and every other part of the system starts working harder to make up the difference.
This guide covers garage door spring adjustment from a homeowner’s point of view. You will learn the signs that your springs need attention, how to check door balance safely, what a technician actually does when adjusting torsion and extension springs, when adjustment is the wrong fix, and how Utah’s weather plays into all of it. If your door is acting up right now, call (844) 971-3667. Estimates are always free.
Safety Warning
Do not attempt to adjust, wind, unwind, or loosen garage door springs yourself. Torsion springs are wound under high torque, and extension springs are stretched under heavy load. A slipped winding bar, a loosened set screw, or a cracked spring fitting can release that energy instantly. If a spring is broken, a cable is loose or frayed, or the door is crooked, leave the door where it is, keep people and pets away, and call a professional.
Table of Contents
- 1. Garage Door Spring Adjustment: Quick Answer Table
- 2. What Garage Door Spring Adjustment Actually Means
- 3. Eight Signs Your Springs Need Adjustment
- 4. How to Check Door Balance Safely
- 5. Adjust or Replace? How to Tell the Difference
- 6. How Technicians Adjust Torsion Springs
- 7. How Technicians Adjust Extension Springs
- 8. Why Garage Door Spring Adjustment Is Not a DIY Job
- 9. Do Not Use the Opener to Cover a Spring Problem
- 10. When Door Weight Changes, Springs Must Change Too
- 11. Utah Weather and Spring Tension
- 12. What Happens During a Professional Spring Adjustment
- 13. How to Keep Your Door Balanced Longer
- 14. Spring Adjustment Service Across Utah
- 15. FAQ: Garage Door Spring Adjustment
Garage Door Spring Adjustment: Quick Answer Table
Use this table to match what your door is doing with the most likely spring issue. It is a starting point, not a diagnosis. A technician should confirm the cause before anyone touches spring tension.
| What You Notice | What It Usually Means | Likely Fix |
|---|---|---|
| Door drifts down after you lift it halfway by hand | Springs have too little tension or are wearing out | Adjustment if springs are healthy; replacement if they are fatigued |
| Door creeps up or flies open on its own | Springs have too much tension | Professional adjustment to reduce tension |
| Door feels very heavy when lifted by hand | Springs have lost tension, are undersized, or one is broken | Inspection first; often replacement |
| Opener strains, slows down, or stops partway | Door is out of balance and the opener is lifting dead weight | Rebalance the springs, then check the opener |
| Door slams the last foot when closing | Low spring tension or a broken spring | Inspection; adjustment or replacement |
| One side of the door sits lower (extension springs) | Uneven tension between the left and right springs | Professional adjustment of both sides |
| Visible gap in a torsion spring’s coils | Broken spring | Replacement, not adjustment |
| Door got harder to lift after adding insulation, windows, or new panels | Door weight now exceeds what the springs were sized for | Re-size and replace springs |
Notice how often the answer is “inspection first.” That is because the symptoms of a spring that needs a small tension tweak and a spring that is close to failing can look identical from the floor. Our signs your spring is about to break guide covers the warning signs of a failing spring in more detail.
What Garage Door Spring Adjustment Actually Means
Every sectional garage door uses a counterbalance system. The springs store energy when the door closes and release it when the door opens, offsetting most of the door’s weight. When the system is set correctly, the door feels light in your hands and an opener only has to provide a small push to move it.
Garage door spring adjustment is the process of fine-tuning that stored energy so it matches the door. Too little tension and the door feels heavy and drifts down. Too much tension and the door wants to rise on its own and may not stay closed firmly. The goal is a door that is close to neutral, which is why a balanced door will stay in place when you stop it halfway.
Torsion Springs
Most modern Utah homes have torsion springs, which mount on a steel shaft above the door opening. They work by twisting. Tension is set by the number of turns wound into the spring, and it is adjusted in small increments with winding bars that fit into a winding cone at the end of the spring. Our torsion spring guide and torsion bar guide explain the parts involved.
Extension Springs
Older homes and some budget installations use extension springs, which run along the horizontal tracks on each side of the door and stretch as the door closes. Tension is set by how far the springs are stretched, which depends on where the spring hooks onto its hanger and on the length of the lift cables. Extension springs work as a pair, so both sides must be set evenly. See our extension springs guide and our comparison of torsion vs extension springs.
Pro Tip
Spring adjustment and spring replacement are related but different jobs. Adjustment fine-tunes healthy springs that are the right size for the door. Replacement swaps out springs that are broken, worn out, or the wrong size. A good technician will tell you which one your door actually needs, and why.
Eight Signs Your Springs Need Adjustment
These are the most common signs that a door’s counterbalance has drifted. Any one of them is worth a closer look. Two or more together usually means it is time for a professional inspection.
1. The Door Will Not Stay Open Halfway
A balanced door should hold its position when you stop it about halfway up by hand. If it slides back down, the springs are not carrying enough of the weight. This is the single most reliable sign of low spring tension. Our door won’t stay open guide covers other causes too.
2. The Door Rises on Its Own
The opposite problem is less common but just as important. If the door creeps upward when disconnected from the opener, or jumps up quickly after you start lifting, the springs have more tension than the door needs. Over-tensioned springs put extra stress on cables, drums, and bearings, and DASMA notes that excessive torque can put excessive force on other counterbalance components.
3. The Door Feels Heavy
When the opener is disconnected, a balanced residential door should be manageable to lift by hand. If it suddenly feels like dead weight, the springs have lost tension, are undersized, or one has broken. Do not keep lifting a door that feels much heavier than normal.
4. The Opener Strains or Slows Down
Openers are designed to move a balanced door, not to lift its full weight. When springs lose tension, the opener has to do more of the work. You may hear the motor laboring, see the door slow down near the top, or notice the opener stop and reverse. Over time, that extra load wears out gears and drive parts. Our opener humming but not moving guide explains what happens when the drive finally gives out.
5. The Door Slams Shut
If the door drops quickly over the last foot or two and hits the floor hard, the springs are not slowing it down the way they should. That can be low tension, or it can be a broken spring. Either way, a slamming door is a safety concern.
6. The Door Hangs Crooked or Uneven
On extension spring doors, uneven tension between the two sides can make one side of the door rise faster or sit lower. On torsion doors, a crooked door is more often a cable or drum problem. Our crooked garage door guide walks through the possibilities. Do not operate a door that is visibly crooked.
7. The Door Jerks or Moves Unevenly
Jerky movement can come from worn rollers, track problems, or a counterbalance system that is out of adjustment. When the springs are not carrying their share, the door can lurch as the opener takes up the slack. See our jerking and jumping door guide for the full list of causes.
8. Springs Were Recently Replaced and the Door Still Feels Wrong
New springs sometimes need a small follow-up adjustment as they settle in, especially if the original installer did not fine-tune the balance. If a recent spring job left your door heavy, light, or noisy, have it checked. DASMA’s spring life guidance warns that an incorrect number of turns can cause problems, including a door drifting down from its open position over time.
How to Check Door Balance Safely
A balance test is the one spring-related check most homeowners can do safely, as long as the springs and cables look intact. It tells you whether the counterbalance system is set close to where it should be. Our dedicated garage door balance test guide covers it step by step, and here is the short version.
Safety Warning
Skip this test and call a professional if you see a gap in a torsion spring, a loose or frayed cable, a cable off its drum, a crooked door, or if you heard a loud bang from the garage. Never pull the emergency release with the door open. A door with a broken spring can fall without warning.
Action Step
- Close the door fully using the opener.
- Pull the emergency release cord to disconnect the door from the opener while the door is closed. Our emergency release guide explains how it works.
- Lift the door by hand to about halfway open, keeping your hands on the handles or lift points, never in the section joints.
- Let go carefully, with your hands ready, and watch what the door does.
- Lower the door, then reconnect it to the opener by running the opener until the trolley reengages.
| What the Door Does at Halfway | What It Means |
|---|---|
| Stays put or moves only a few inches | Springs are close to balanced. No adjustment needed. |
| Drifts steadily downward | Too little tension or worn springs. Call for an inspection. |
| Drifts steadily upward | Too much tension. Call for a professional adjustment. |
| Drops quickly | Possible broken spring. Stop and call a professional. |
If the door fails the balance test, the next question is whether adjustment will fix it or whether the springs themselves are the problem. That is the most important judgment call in this whole guide.
Adjust or Replace? How to Tell the Difference
Adjustment works when the springs are the right size for the door, in good condition, and simply set with slightly too much or too little tension. It does not fix a spring that is broken, rusted through, worn out, or mismatched to the door. Here is how technicians usually think about it.
| Situation | Adjust | Replace |
|---|---|---|
| Springs are fairly new and correctly sized, door slightly out of balance | Yes | No |
| Door was balanced, then drifted over several years | Sometimes, if springs are healthy | Often, if springs are near end of life |
| Door needs another adjustment soon after the last one | No, the springs are fatiguing | Yes |
| Visible gap, crack, or break in a coil | Never | Yes |
| Heavy rust or pitting on the coils | No | Yes |
| Door weight changed (insulation, windows, new panels) | Rarely enough | Usually re-sized springs |
| Mismatched springs on a two-spring door | No | Yes, as a matched set |
| Extension springs stretched out with gaps between coils at rest | No | Yes |
The biggest trap is adding tension to a tired spring. As springs approach the end of their cycle life, they gradually lose some of their ability to hold torque. Winding more turns into a fatigued spring can make the door feel right again for a while, but it also raises the stress on the spring wire and on the cables, drums, and bearings it pulls against. That is a short-term fix with long-term costs.
DASMA’s technical guidance is clear that the number of turns on a torsion spring should always follow the garage door manufacturer’s installation instructions. If a spring needs far more turns than the specification calls for to hold the door, the spring is the problem, not the adjustment. Learn more in our guide to how long garage door springs last.
Pro Tip
If your door has two torsion springs and one breaks, replacing both is usually the smart move, because they have the same age and the same number of cycles. A new spring paired with an old one makes balancing harder and often leads to a second service call.
How Technicians Adjust Torsion Springs
We are describing this process so you know what a professional visit looks like and can recognize good work. This is not a set of instructions. Torsion spring adjustment requires the right tools, training, and a clear understanding of how the whole counterbalance system works together.
Safety Warning
Never use screwdrivers, pliers, or anything other than properly sized winding bars on a torsion spring, and never loosen the set screws on a winding cone. Once the set screws are loose, the only thing holding back the spring’s stored energy is whatever is in the winding cone. Homeowners have been seriously injured attempting this.
Here is what a trained technician typically does:
- Inspects first. Before touching tension, a technician checks the springs for gaps, rust, and wear, and looks at the cables, drums, center bearing plate, end bearing plates, and shaft. Adjusting springs on a door with a frayed cable or a cracked cone only moves the problem around.
- Secures the door. The door is closed, the opener is disconnected or unplugged, and the door is secured so it cannot move during the work.
- Uses correctly sized winding bars. Solid steel bars that fit the holes in the winding cone snugly. One bar always stays in the cone whenever the set screws are loose.
- Adjusts in small increments. Tension is added or removed a little at a time, typically in quarter turns, rather than all at once.
- Matches both springs. On a two-spring door, both springs are adjusted by the same amount so the shaft is not twisted unevenly.
- Resets the set screws and stretch. The set screws are retightened to the proper torque, and the spring’s stretch is checked. DASMA notes that too little stretch lets the coils scrape against each other, and too much can cause the spring to snake and rub.
- Tests and retests. The technician runs a balance test, operates the door by hand and with the opener, and repeats small adjustments until the door is balanced.
- Checks the opener and safety reversal. Once the door is balanced, force settings and the safety reversal system are checked, since a rebalanced door can change how the opener behaves.
Winding direction matters too. A two-spring system has a left-wound and a right-wound spring, and DASMA lists winding a torsion spring backwards as a safety issue for the installer. A professional confirms the spring type before applying any turns.
Utah Note
Many newer homes along the Wasatch Front came with builder-grade doors and a single torsion spring sized close to the minimum for the door. Those springs tend to go out of balance sooner, and they often need replacement instead of adjustment. Our builder-grade upgrade guide explains why upgrading to a two-spring setup with higher-cycle springs often pays off.
How Technicians Adjust Extension Springs
Extension springs are adjusted differently from torsion springs, but they are no less dangerous. A stretched extension spring under load stores a lot of energy, and a spring that breaks without a containment cable can turn into a projectile. Here is what a professional extension spring adjustment generally involves:
- Relieving tension first. Extension springs carry the least tension when the door is fully open. The technician opens the door and secures it in place before making any changes, so the springs are not under full load.
- Moving the attachment point. Tension is changed by moving the spring’s hook to a different hole on its hanger, or by adjusting the lift cable length at the bottom bracket or pulley. Each change makes the spring stretch more or less when the door closes.
- Adjusting both sides evenly. Because extension springs work as a pair, both sides must carry the same share of the load. Uneven tension makes the door rise crooked and wears out cables and rollers on one side.
- Installing safety containment cables. A safety cable should run through the center of each extension spring. If a spring breaks, the cable keeps it from flying across the garage. Many older installations are missing these, and a technician should add them.
- Testing balance. The door is reconnected, tested by hand, and adjusted again if needed.
If your extension springs look stretched out, with visible gaps between the coils while the door is open, they have lost their strength and need to be replaced, not adjusted. DASMA’s spring color code sheet notes that extension springs are sized as a pair for the door weight, so both should be replaced together.
Pro Tip
If you have an older door with extension springs, ask about converting to torsion springs when the time comes for replacement. Torsion systems are generally smoother, easier to balance, and keep the spring energy contained on a shaft above the door. Our torsion vs extension springs guide compares the two.
Why Garage Door Spring Adjustment Is Not a DIY Job
We understand the appeal of fixing things yourself, and there are plenty of garage door tasks homeowners can handle. Spring adjustment is not one of them. Here is why we always recommend leaving it to a trained technician:
- Stored energy. Springs hold enough energy to lift a heavy door. When that energy is released unexpectedly, it can break bones, cause head injuries, or worse.
- Tool slips happen fast. A winding bar that slips out of a cone, or a screwdriver used in its place, can spin with tremendous force.
- Hidden damage. Cracked spring cones, worn cables, and fatigued springs can look normal until they are put under new stress. DASMA warns that even a cracked or broken cast spring fitting can cause spring failure and injury to the installer.
- Wrong spring, wrong turns. DASMA lists applying a spring to the wrong door and applying an incorrect number of turns as installation factors that shorten spring life and create safety issues.
- Industry guidance. DASMA’s spring color code technical data sheet states that replacement of springs on garage doors should only be performed by a trained door systems technician.
Our can you replace garage door springs yourself article and our guide to DIY vs professional garage door repairs go deeper on where the line is.
What Homeowners Can Safely Do
Staying hands-off the springs does not mean you are powerless. These tasks are safe and genuinely helpful:
- Watch and listen to the door every time it runs, and note any change in speed, sound, or smoothness.
- Run a balance test every few months if the springs and cables look intact.
- Look at the springs from a safe distance for gaps, rust, or stretched coils. Do not touch them.
- Keep the door’s path clear and test the safety reversal system monthly.
- Lubricate rollers, hinges, and bearings as part of routine maintenance. Our lubrication guide covers what to use and where.
- Call a professional at the first sign the door is out of balance, instead of waiting for a spring to break.
Do Not Use the Opener to Cover a Spring Problem
One of the most common mistakes we see is turning up the opener’s force setting to make an out-of-balance door work again. It feels like a fix, because the door starts moving. But it hides the real problem and creates new ones:
- It overloads the opener. The motor, gears, and drive were designed to move a balanced door. Lifting extra weight every cycle wears them out early.
- It weakens the safety reversal. Higher force means the opener pushes harder before it senses an obstruction and reverses. That is the opposite of what you want around kids, pets, and cars.
- It does nothing for the springs. The springs keep losing tension or keep heading toward failure. When one finally breaks, the opener may try to lift the full weight of the door.
Force and travel settings have their place, and our guide to adjusting travel limits and force settings explains when to use them. But they should only be adjusted after the door itself is properly balanced.
Safety Warning
After any spring adjustment or opener setting change, test the safety reversal system. Place a 1-1/2 inch thick board (or a 2×4 laid flat) on the floor under the center of the door and close it with the opener. The door should reverse when it hits the board. If it does not, stop using the opener and call for service.
When Door Weight Changes, Springs Must Change Too
Springs are sized for a specific door weight. When that weight changes, simply adding turns or stretch is rarely the right answer. The springs may need to be re-sized and replaced. DASMA specifically warns that actions such as painting a door or adding components can push the door weight beyond the manufacturer’s specifications.
Common changes that add weight include:
- Adding an insulation kit to an uninsulated door. See our garage door insulation guide.
- Adding windows or upgrading to heavier glass. Our window inserts guide covers options.
- Replacing a panel with a heavier one or adding struts for reinforcement. See our struts guide.
- Adding decorative hardware, faux wood overlays, or multiple coats of paint.
- Hanging anything from the door or its tracks, which DASMA advises against.
If you have made any of these changes and the door now feels heavier, slower, or harder on the opener, ask a technician to weigh the door and check whether the springs are still correctly sized. A spring sized for the old weight will be overworked from day one.
Action Step
Planning to insulate, add windows, or upgrade your door hardware this winter? Call (844) 971-3667 before you start. We can tell you whether your current springs can handle the added weight, and help you avoid a balance problem after the project is done.
Utah Weather and Spring Tension
Utah’s climate does not change the physics of a garage door, but it does change how hard the springs work and how quickly problems show up. DASMA’s spring life guidance lists extreme heat or cold, frequent precipitation, and corrosive environments as factors that can shorten spring life. Depending on where you live in Utah, you may deal with all of them.
Cold Mornings and Big Temperature Swings
Fall and winter in northern Utah bring cold mornings and big swings between night and afternoon temperatures. Cold thickens lubricants and stiffens weatherstripping, which makes the door harder to move and can make an already marginal spring setup feel worse. A worn spring is working hardest when the door is cold and stiff, so the first cold snaps of the season are a common time for weak springs to give out. Our temperature changes guide and winter garage door problems guide cover this in detail.
Road Salt and Moisture
Snowmelt and road salt tracked in on vehicles keep the garage damp through winter. DASMA notes that rust reduces the effective area of spring wire and can create corrosion pits where fatigue cracks start. Rusty springs should not be adjusted to squeeze more life out of them. They should be evaluated for replacement.
Doors Left Open
DASMA recommends keeping doors closed where possible in climates with extreme heat or cold. In Utah, that applies year-round, from summer heat in St. George to winter cold in Cache Valley and Park City. Keeping the door closed protects the springs and the rest of the hardware from temperature and moisture swings.
Utah Note
Late October and November are the best time to have your springs checked in northern Utah. A balance check and tune-up before the first hard freeze can catch a weak spring before it breaks on a snowy morning. Our fall maintenance checklist covers everything to look at before winter.
What Happens During a Professional Spring Adjustment
Knowing what to expect makes it easier to spot quality work and avoid a rushed job. When Advanced Door comes out for a door that is out of balance, here is what the visit looks like:
- A conversation first. We ask what you have noticed, when it started, and whether anything about the door has changed, such as new insulation, windows, or a recent repair.
- A full counterbalance inspection. Springs, cables, drums, bearings, shaft, and hardware all get checked, because a balance problem is rarely isolated to one part.
- A balance test. We disconnect the opener and test the door by hand so you can see the problem for yourself.
- An honest recommendation. If adjustment will fix it, we tell you. If the springs are worn, mismatched, or undersized, we explain why replacement is the better option and give you a clear estimate before any work starts.
- The work itself. Adjustment or replacement is done with the proper tools and procedures described above.
- Lubrication and hardware check. Springs, hinges, rollers, and bearings are lubricated as appropriate, and loose hardware is tightened.
- Opener and safety testing. Force settings, travel limits, photo eye sensors, and the safety reversal system are tested after the door is balanced.
- A walkthrough. We show you how the door behaves now and what to watch for going forward.
Our service call guide covers the full visit in more detail. If you are comparing quotes, our article on why garage door estimates differ explains what to ask so you are comparing the same work.
Pro Tip
When springs do need replacement, the type of spring matters as much as the installation. Advanced Door installs lifetime warranty springs rated for two to three times the cycle count of many standard springs. They cost more up front, but they hold their balance longer and you will not be paying for the same repair again in a few years.
How to Keep Your Door Balanced Longer
Springs wear out eventually no matter what, but good habits slow the process and help you catch balance problems before they turn into breakdowns. DASMA notes that regular lubrication of springs, as the manufacturer requires, helps maximize spring cycle life.
| Task | How Often | Who Does It |
|---|---|---|
| Watch and listen to the door during normal use | Every use | Homeowner |
| Test the safety reversal system | Monthly | Homeowner |
| Visual check of springs and cables from a distance | Monthly | Homeowner |
| Balance test (only if springs and cables look intact) | Every few months | Homeowner |
| Lubricate rollers, hinges, and bearings | Every 6 months | Homeowner or technician |
| Lubricate springs and inspect the counterbalance system | Yearly | Technician |
| Professional tune-up with balance check and adjustment | Yearly, ideally in fall | Technician |
For the full schedule, see our garage door maintenance schedule and our tune-up guide. A yearly tune-up is the easiest way to keep spring tension where it should be.
- Keep the door closed when you are not using it, especially during extreme heat or cold.
- Keep the garage as dry as you can in winter by knocking snow off vehicles and clearing meltwater.
- Do not hang things from the door or its tracks.
- Ask before adding weight with insulation, windows, or decorative hardware.
- Do not ignore small changes. A door that feels a little heavier this month usually feels a lot heavier in a few months.
Spring Adjustment Service Across Utah
Advanced Door provides garage door spring adjustment, spring replacement, and full counterbalance service throughout Utah. Call the office closest to you:
- Ogden and Weber County: (801) 430-9021. See our Ogden garage door repair page.
- Logan and Cache Valley: (435) 363-4929. See our Logan and Cache Valley page.
- Draper and the south valley: (801) 967-8998. See our Draper garage door repair page.
- Everywhere else in Utah: (844) 971-3667, including Provo and Utah County, Layton and Davis County, and Park City.
If a spring has already broken, read our broken spring guide for what to do while you wait, and our spring replacement cost guide for what affects the price. For an overview of everything we fix, see our Utah garage door repair guide.
Call (844) 971-3667 today for a free estimate. Current offers: $100 off any new door or 10% off any service call (offers cannot be combined).
FAQ: Garage Door Spring Adjustment
How do I know if my garage door springs need adjustment?
The most reliable sign is a door that will not stay in place when you lift it halfway by hand with the opener disconnected. Other signs include a door that feels heavy, creeps up on its own, slams shut, or makes the opener strain. Any of these is a reason to have the springs inspected.
Can I adjust my garage door springs myself?
We strongly recommend against it. Torsion and extension springs store enough energy to cause serious injury if a tool slips or a part fails. DASMA states that spring replacement should only be performed by a trained door systems technician, and adjustment involves the same stored energy.
What is the difference between spring adjustment and spring replacement?
Adjustment fine-tunes the tension on healthy springs that are the right size for the door. Replacement swaps out springs that are broken, rusted, worn out, mismatched, or no longer sized for the door’s weight. A technician should inspect the springs before deciding which one you need.
Why does my garage door slide down when I lift it halfway?
The springs are not carrying enough of the door’s weight. That can mean the tension needs adjustment, or it can mean the springs are wearing out. If the door drops quickly, a spring may be broken. Stop using the door and call a professional.
Will adding more tension make old springs last longer?
No. Adding turns to a fatigued spring may make the door feel balanced for a while, but it increases stress on the spring and on the cables, drums, and bearings. DASMA notes that excessive torque puts excessive force on other counterbalance components. Worn springs should be replaced.
Can I turn up the opener force instead of adjusting the springs?
No. Raising the force setting makes the opener lift weight the springs should be carrying, which wears out the opener and makes the safety reversal less sensitive. Balance the door first, then adjust opener settings only if needed.
How often should garage door springs be adjusted?
Correctly sized, healthy springs should not need frequent adjustment. A yearly tune-up with a balance check is usually enough. If your door needs adjustment again soon after the last one, the springs are likely fatiguing and should be evaluated for replacement.
Does cold weather affect garage door spring tension?
Cold thickens lubricants and stiffens the door’s moving parts, which can make a marginal spring setup feel worse. DASMA lists extreme cold among the conditions that can shorten spring life. In northern Utah, fall is the best time to have springs checked before winter.
References: DASMA Technical Data Sheet #190, Factors Affecting Spring Cycle Life (incorrect turns, improper stretch, added door weight, climate, and lubrication) and DASMA Technical Data Sheet #171, Official Color Codes for Torsion and Extension Springs (spring identification, paired extension springs, and why spring replacement belongs with a trained door systems technician).
Get a Free Estimate from Advanced Door
Door heavy, drifting, or slamming? Get a safe, professional spring adjustment or an honest replacement recommendation.
Serving Ogden, Salt Lake City, Provo, Park City, Logan, and all of Utah
Call for a free estimate. No pressure, no hidden fees.
Current offers: $100 off any new door or 10% off any service call
(Offers cannot be combined)
