Garage door slams shut? In most cases, a garage door that slams shut or closes too fast has a spring problem. The springs are supposed to carry almost all of the door’s weight. When a spring breaks, wears out, or was sized wrong, the door gets heavy and gravity takes over on the way down. A broken or frayed lift cable, a disconnected opener, worn opener parts, or a door that has gotten heavier can cause the same thing. A door that slams is not just loud. It is a heavy object falling with too little control, so stop using it, keep people and pets clear, and have a technician check the springs and cables. Advanced Door is Utah’s #1 rated garage door company: family owned since 1994, 4.9 stars, 30,000+ five-star reviews, and the only company in Utah offering a lifetime warranty on parts and labor. Call (844) 971-3667 for a free estimate.

Last updated: October 2026
You press the button, the door starts down like normal, and then the last couple of feet it drops and hits the concrete with a bang that shakes the whole garage. Or maybe you pulled the red emergency cord, and the door came down so fast you had to jump back. Either way, you now have a garage door that slams shut, and you have a good reason to be uneasy about it.
Here is the short version: a healthy garage door should never fall. It should move at a steady, controlled speed all the way down and touch the floor gently. If it speeds up, drops, or slams, something in the system that is supposed to hold the door’s weight is no longer doing its job. That is usually the springs, sometimes the cables, and occasionally the opener.
This guide walks through the 9 most common reasons a garage door slams shut, how to tell them apart by the way the door behaves, which quick checks are safe for a homeowner, what you should never try, and how a technician actually fixes it. It is written for Utah homeowners, because our cold snaps, road salt, and snow-packed driveways add a few causes of their own.
If your door is slamming right now, the safest move is to stop using it and call (844) 971-3667. Estimates are always free.
Table of Contents
- 1. Why a Garage Door Should Never Slam
- 2. Is a Garage Door That Slams Shut Dangerous?
- 3. What to Do Right Now
- 4. 9 Reasons Your Garage Door Slams Shut
- 5. Reading the Pattern: When and How It Slams
- 6. Symptom Chart: Likely Cause and Next Step
- 7. Safe Checks You Can Do Yourself
- 8. What Not to Do
- 9. How a Technician Fixes a Door That Slams
- 10. Utah Conditions That Make Slamming More Likely
- 11. How to Keep Your Door From Slamming Again
- 12. What Affects the Cost of the Repair
- 13. How Advanced Door Helps
- 14. Frequently Asked Questions
Why a Garage Door Should Never Slam
To understand why a garage door slams shut, it helps to know who is really doing the lifting. It is not the opener. Your garage door is heavy, and the springs are wound or stretched to counterbalance almost all of that weight. On a torsion system, the springs sit on a bar above the opening and turn cable drums at each end. On an extension system, the springs stretch along the horizontal tracks and pull the cables through pulleys. Either way, the springs and cables are what hold the door up.
The opener is a guide, not a hoist. It pushes and pulls the door along the track and controls the speed, but it is designed to move a balanced door, not to hold up a heavy one. That is why a properly balanced door can be lifted by hand with modest effort and will stay in place when you let go about halfway up.
When the balance between the door’s weight and the spring force is lost, the door becomes heavier than the system was set up to handle. On the way down, that extra weight shows up as speed. The door accelerates, the opener cannot hold it back, and the bottom hits the floor hard. If you want the full picture of how these parts work together, our guide on how a garage door works walks through every component, and our garage door weight guide shows why that balance matters so much.
Pro Tip
A door that opens fine but slams on the way down is still a balance problem. Opening, the opener is fighting the extra weight and you may only notice it as a slower start or a strained motor. Closing, gravity is helping the extra weight, so that is where the problem becomes obvious.
Is a Garage Door That Slams Shut Dangerous?
Yes. A garage door that slams shut should be treated as a safety problem, not a noise problem. Here is why:
- The door is heavy. Without working springs, you are dealing with the full weight of a large, moving steel, wood, or composite door. That weight can seriously injure someone caught under it.
- It moves faster than the safety system expects. Photo eye sensors and the opener’s auto-reverse are designed for a door moving at normal speed. A door that is falling, or that is not connected to the opener at all, may not stop or reverse in time.
- It is often a sign of a second failure coming. If one spring on a two-spring door has broken, the other one is carrying more load than it was designed for. Cables and bottom brackets are also under extra stress.
- It damages the door and opener. Repeated slamming can crack or bend the bottom section, loosen hinges and roller brackets, strip opener gears, and chip the concrete.
- Fingers and hands are at risk. If someone tries to catch or guide a falling door by hand, the gaps between sections can pinch. DASMA specifically warns never to place fingers between door sections.
Safety Warning
If your garage door slams shut, stop using it. Keep children, pets, vehicles, and people out of the door’s path. Do not try to catch, hold, or guide a door that is falling. Springs, cables, and bottom brackets are under high tension and should only be handled by a trained technician.
What to Do Right Now
What you should do depends on where the door is right now.
If the door is closed
- Leave it closed. A closed door is the most stable, lowest-energy position.
- Unplug the opener or turn off its circuit so no one in the house opens it by remote, keypad, or app.
- Do not pull the emergency release to test it by hand unless the springs and cables clearly look intact (more on that below).
- If you need your car, consider getting a ride rather than forcing the door open. Our guide to opening a garage door with a broken spring or cable explains the risks.
- Call a technician and describe exactly what happened.
If the door is open
- Do not close it with the opener just to see what happens. If the springs have failed, the door can drop the moment it starts down.
- Do not pull the emergency release cord. With the opener disconnected, an unbalanced door can come down on its own, very fast.
- Keep everyone and everything out from under the door. Move the car out only if you can do it without driving under a door you are worried about.
- Unplug the opener so nobody closes it by accident, then call for service.
Action Step
Before you call, take a quick look (from a safe distance) at the springs above the door or along the tracks and the cables at the bottom corners. Note anything that looks broken, gapped, loose, or frayed. A photo helps. Then call (844) 971-3667 and tell us what you saw. That helps us bring the right parts the first time.
For more on handling a fresh spring break, see what to do when a garage door spring breaks. If a cable is the problem, see garage door cable snapped: what to do.
9 Reasons Your Garage Door Slams Shut
These are the most common causes, roughly in the order we see them. More than one can be true at the same time. A worn spring often breaks a worn cable, and a slamming door often damages the opener.
1. A broken torsion spring
This is the number one reason a garage door slams shut. Most modern residential doors use torsion springs mounted on a bar above the opening. When a torsion spring breaks, you will usually see a gap of an inch or two somewhere in the coil, and many homeowners report a loud bang from the garage when it happened.
On a door with one torsion spring, a break leaves the door with almost no counterbalance. On a door with two springs, one break leaves the remaining spring trying to do the work of two. Either way, the door is now much heavier than the opener is designed to control, and it will drop or close hard. Many openers will also refuse to lift it, or will lift it a few inches and stop.
Learn to spot the warning signs before a break in 7 signs your garage door spring is about to break, and see how the spring bar works in our torsion bar guide.
2. Worn-out springs that have lost tension
Springs do not always break cleanly. Every spring is rated for a certain number of open and close cycles, and as it ages, the steel fatigues and the spring slowly loses force. The door does not fall all at once. Instead, it gets a little heavier every month. One day you notice it drifts down when you leave it halfway, or it speeds up over the last few feet.
This is the sneaky version of the problem, because the door still works. It just works harder and closes harder. If your springs are original to a door that is more than a few years old and gets daily use, a weak spring is a strong possibility. See how long garage door springs last for what affects spring life.
3. A broken or stretched extension spring
Older homes and some lighter doors use extension springs that run alongside the horizontal tracks. When one breaks, the door becomes lopsided as well as heavy. It may close crooked, slam on one side, or bind in the track. Extension springs can also stretch out and weaken over time, which gives you the same slow-slam pattern as a worn torsion spring.
Extension springs should always have a safety cable running through the center of each spring. If a spring breaks without one, pieces can fly across the garage. DASMA recommends a safety inspection if your extension springs do not have safety cables. Our extension spring guide and torsion vs extension springs comparison cover the differences.
Safety Warning
Extension springs are under high tension when the door is closed. Do not try to unhook, adjust, or replace them yourself. If you see a broken extension spring with no safety cable, keep everyone away from the tracks and call a technician.
4. A frayed, broken, or slipped lift cable
The lift cables connect the springs to the bottom corners of the door. If a cable frays, breaks, or comes off its drum, that side of the door loses its support. The result is often a door that drops on one side, hangs crooked, or slams down unevenly. Sometimes a cable lets go only after a spring has already failed and the door has started slamming.
Look for loose cable hanging near the bottom corner, a cable that is wound unevenly on the drum, or broken strands. DASMA notes that because of the spring tension involved, cables should be replaced only by a trained technician. See what happens if a garage door cable breaks and our cable drum guide.
5. The wrong springs from a past repair
Springs have to be matched to the door’s weight, height, and drum size. If a previous repair used springs that were the wrong size, the wrong wire gauge, or the wrong number of turns, the door may never have been properly balanced. Sometimes this happens after a DIY spring swap. Sometimes it happens when a company installs whatever springs are on the truck instead of the right ones.
Another common issue is replacing only one spring on a two-spring door. The new spring and the old spring have different strength, so the door is out of balance from day one and the older spring is likely to fail next. DASMA recommends replacing both springs, even if only one is broken. If you are not sure what you have, our spring color code and identification guide can help you understand the markings.
6. The door got heavier, but the springs did not change
Springs are set for the door’s weight at the time of installation. If the door gets heavier, the old setup is no longer enough. Common reasons a door gains weight include:
- Adding an insulation kit to an uninsulated door
- Replacing a damaged section with a heavier or different panel
- Adding windows, decorative hardware, or a new layer of trim
- Wood doors absorbing moisture, especially after wet weather if the finish is worn
- Snow and ice packed onto the bottom section or the outside face in winter
Any time the door’s weight changes, the spring balance should be checked. This is easy for a technician to do during a visit, and it can prevent a slow slide into slamming. Our panel replacement guide covers what to consider when swapping sections.
7. The emergency release was pulled on an unbalanced door
When the opener is connected, it can sometimes mask a balance problem by controlling the door’s speed. Pull the red emergency release cord, and that control is gone. If the springs are weak or broken, the door will fall on its own as soon as it is disconnected. This is how many people discover their spring problem: the power goes out, they pull the cord, and the door drops.
This is also why we tell homeowners never to pull the release when the door is open unless they are sure the springs and cables are good. If you need to use it during a power outage, see our emergency release guide and power outage guide first.
8. Opener problems: stripped gears, a broken trolley, or a loose drive
Sometimes the springs are fine and the opener loses its grip on the door. A stripped drive gear, a broken trolley or carriage, or a chain or belt that has slipped can all let the door move with less control than it should. On a perfectly balanced door, that usually means the door just stops or drifts. On a door that is even slightly heavy, it means the door can come down faster than normal.
Opener settings can also make a normal close feel violent. If the close travel limit is set too far, the opener keeps driving the door after it reaches the floor, which can make the door bang, flex, and sometimes reverse. Our guides to travel limits and force settings and an opener that hums but does not move explain these parts in more detail.
Pro Tip
Turning up the force setting is not a fix for a heavy door. It only lets the opener push harder against a problem, and it makes the safety reverse less sensitive. If your opener seems to need more force than it used to, the door’s balance is the first thing to check.
9. A worn bottom seal or uneven floor (the good-news cause)
Not every bang means a broken spring. If the rubber seal on the bottom of the door is flattened, cracked, torn, or missing, the bottom edge of the door hits the concrete metal-to-floor. That can make a normal, controlled close sound like a slam. A sunken or cracked slab can do the same thing on one side.
The difference is speed. If the door moves at a steady pace the whole way and only the final contact is loud, the seal is a likely suspect. If the door speeds up or drops before it touches, look at the springs and cables first. See our bottom seal replacement guide and gap at the bottom guide.
Reading the Pattern: When and How It Slams
The way your garage door slams shut is one of the best clues to what is wrong. Pay attention to when it happens and what the door does just before.
It speeds up over the last 2 to 3 feet
This is the classic sign of weak or worn springs. Near the bottom, the springs are at their lowest tension and the door’s weight is mostly hanging on the cables, so any loss of spring force shows up most at the end of travel. It can also point to a spring setup that was never sized correctly.
It drops from the top or falls the whole way
A door that falls from fully open, or that you cannot hold up at all, usually has a broken torsion spring, both springs failing, or a broken cable. This is the most dangerous version. Do not operate the door.
It only slams when the opener is disconnected
If the door closes normally with the opener but drops when you pull the release, the opener has been masking a balance problem. The springs are weak or broken, and the opener has been working harder than it should.
It closes crooked or one side hits first
Uneven slamming points to one side: a broken extension spring, a frayed or slipped cable, a cable drum issue, or a damaged bottom bracket. You may also see the door hang at an angle when it is open. See our crooked garage door guide.
It moves at a steady speed and only the final contact is loud
That points to the bottom seal, the floor, or a close limit that is set too far. These are usually the least urgent causes, though the limit setting should still be corrected.
It slammed once after a loud bang from the garage
A loud bang when nobody was using the door is a very common sign that a torsion spring just broke. Treat the door as unsafe until someone checks it.
Garage Door Slams Shut: Symptom Chart
Use this chart to match what you are seeing with the most likely cause. It is a starting point, not a diagnosis.
| What You See | Likely Cause | Safe to Use? | Who Should Fix It |
|---|---|---|---|
| Door falls from fully open or cannot be held up | Broken torsion spring, broken cable | No. Stop using it. | Technician |
| Speeds up over the last few feet | Worn or weak springs, wrong springs | Not recommended | Technician |
| Drops only after pulling the emergency release | Weak or broken springs masked by the opener | No. Reconnect only after inspection. | Technician |
| Slams on one side or closes crooked | Extension spring, frayed or slipped cable, drum issue | No. Stop using it. | Technician |
| Loud bang from garage, then door feels heavy | Torsion spring just broke | No. Stop using it. | Technician |
| Opener strains to lift, then door comes down hard | Unbalanced door, sometimes with opener wear | Not recommended | Technician |
| Slams after new panel, insulation, or windows | Door heavier than springs are set for | Not recommended | Technician |
| Steady speed, only the final contact is loud | Worn bottom seal, uneven floor, close limit too far | Usually, with care | Homeowner or technician |
If you are unsure which row fits, or more than one fits, assume the more serious cause and leave the door alone until it is inspected.
Safe Checks You Can Do Yourself
You do not need to touch springs or cables to learn a lot about why your garage door slams shut. These checks are look-and-listen only.
1. Look at the springs from a distance
With the door closed, look at the torsion spring above the door. A broken spring usually shows a clear gap in the coils. On extension springs, look along each horizontal track for a spring that is stretched, separated, or hanging loose. Do not touch them.
2. Look at the cables
Look at the bottom corners of the door where the cables attach, and at the drums above the door on a torsion system. Check for frayed strands, slack cable, or cable that has jumped off the drum. Again, look only.
3. Watch a full cycle from a safe spot
If the springs and cables look intact and the door is not falling, stand well to the side and watch one full close. Note whether it speeds up, where it speeds up, and whether one side hits first. If it drops or slams hard, stop and do not run it again.
4. Check the bottom seal
With the door closed, look at the rubber seal along the bottom. Is it flattened, cracked, missing in places, or letting in daylight? A bad seal will not cause a fast close, but it can make a normal close sound much worse.
5. Consider a balance test, only if everything looks intact
A balance test tells you whether the springs are doing their job. With the door fully closed, you disconnect the opener with the emergency release, lift the door by hand to about halfway, and see if it stays put. A door that drifts down is heavy. A door that falls is a spring or cable problem.
Safety Warning
Skip the balance test if you see any broken spring, gap in the coils, loose or frayed cable, or if the door already falls or slams. Never pull the emergency release with the door open. Keep your hands on the handles, not between sections, and have a second person nearby. If you have any doubt, let a technician do it. Our balance test guide explains the full process and its limits.
If any of these checks point to springs or cables, stop there and call (844) 971-3667.
What Not to Do When Your Garage Door Slams Shut
Most garage door injuries we hear about start with a well-meaning fix. Avoid these:
- Do not adjust, wind, or unwind springs. Torsion springs store a lot of energy, and winding bars can slip. This is the most dangerous job on a garage door. See can you replace garage door springs yourself.
- Do not loosen the bottom brackets. DASMA notes that bottom brackets are connected to the springs and are under extreme tension. They should only be adjusted by a trained technician.
- Do not crank up the opener force. More force does not fix a heavy door. It makes the safety reverse less sensitive and wears out the opener faster.
- Do not replace just one spring on a two-spring door. DASMA recommends replacing both, so the door stays balanced and the second spring does not fail right after.
- Do not keep using the door because it still works. A slamming door damages the opener, the bottom section, and the hinges every time it runs, and the next failure is often bigger.
- Do not rely on clamps, straps, or wood blocks as a long-term fix. They can help hold a door in place in an emergency, but they are not a repair.
If you are weighing what you can safely handle, our guide to safe DIY vs professional garage door repairs draws the line clearly.
How a Technician Fixes a Garage Door That Slams Shut
A proper repair is not just swapping one broken part. It is getting the whole system back into balance and making sure the safety features work. Here is what a good service call looks like:
- Secure the door. The technician makes sure the door cannot move unexpectedly before working on it.
- Inspect the full lift system. Springs, cables, drums, bearings, center bracket, bottom brackets, rollers, hinges, and track all get checked. A slamming door often damages more than one part.
- Identify the right springs. The door’s weight, height, and track setup determine the spring size. The right springs are matched to the door, not to what happens to be on the truck.
- Replace failed or worn parts. On a two-spring door, both springs are replaced together. Frayed or kinked cables are replaced as a pair.
- Balance the door. Spring tension is set so the door stays put at about halfway and lifts with modest effort.
- Check the opener. The technician looks for gear, trolley, and drive damage from the extra load, then resets force and travel limits for the newly balanced door.
- Test the safety features. Photo eyes and the auto-reverse are tested so the door reverses when it should. See our sensor alignment guide.
- Run it several times. The door should open and close smoothly, at a steady speed, and touch down gently.
If the opener took a beating, you may also be deciding whether to fix it or replace it. Our repair or replace your opener guide can help with that call.
Utah Conditions That Make Slamming More Likely
Garage doors fail everywhere, but a few Utah conditions make spring and cable trouble more common here.
Utah Note
Cold snaps and big temperature swings. Steel springs that are already worn tend to give out when they are worked hard in cold weather. Along the Wasatch Front, in Cache Valley, and in mountain towns, the first real cold snap of fall is often when a tired spring finally breaks. If your springs are aging, the weeks before winter are a good time to have them checked. See our fall maintenance checklist and winter problems guide.
Utah Note
Road salt and slush. Cars bring salty slush into the garage all winter. That moisture sits near the bottom of the door, where the cables and bottom brackets live, and it speeds up rust. Corroded cables and brackets are weaker, and rust on springs adds friction and stress. Our rust prevention guide covers what to watch for.
Utah Note
Snow and ice on the door. Wind-driven snow and ice can build up on the bottom section and the outside face of the door. That extra weight can make a borderline door slam when it closes. It can also freeze the bottom seal to the slab, so the door bounces or the opener strains on the next open.
Older homes in Salt Lake City, Ogden, and Logan often have original springs or extension spring systems that are well past their prime. Newer subdivisions in Draper, Lehi, and Utah County often have builder-grade springs sized right at the minimum. Both groups see a lot of worn-spring slamming.
How to Keep Your Garage Door From Slamming Again
The best fix is the one you never need. A few habits go a long way:
- Get a yearly inspection. DASMA recommends an annual visit from a trained door systems technician. A tune-up catches weak springs and frayed cables before they fail. See our garage door tune-up guide.
- Do monthly look-and-listen checks. Watch the door run, look at the springs and cables, and listen for new noises. Our maintenance schedule lays out what to check and when.
- Lubricate the right parts. Springs, hinges, rollers, and bearings benefit from a garage door lubricant. Do not use grease on the tracks. See how to lubricate a garage door.
- Replace springs as a pair. If one breaks, replace both.
- Rebalance after changes. New panels, insulation, windows, or hardware all change the door’s weight.
- Keep the bottom seal in good shape. A healthy seal cushions the close, blocks water, and keeps out pests.
- Test the auto-reverse. Check monthly that the door reverses when it meets an obstruction and when the sensor beam is blocked.
Pro Tip
When we replace springs, we install our lifetime warranty springs, built for 2x to 3x the cycles of standard springs. Longer-lasting springs mean fewer chances for a weak or broken spring to turn your door into a slamming door. Learn more in our spring replacement guide.
What Affects the Cost of the Repair
Because a garage door that slams shut can have several causes, the repair can range from a simple seal replacement to a full spring and cable job. The main factors are:
- Which part failed. A bottom seal, a spring, a cable, or the opener are very different jobs.
- Spring type and count. Torsion or extension, one spring or two, and the size of the springs.
- Whether cables need replacing. Frayed or kinked cables are replaced with the springs when needed.
- Door size and weight. Larger, heavier, insulated, and wood doors need heavier springs and hardware.
- Collateral damage. Slamming can bend the bottom section, crack brackets, or damage the opener.
- Timing. After-hours or emergency calls can affect the cost.
Estimates are always free, and we explain what we found and why before any work starts. For more detail, see our spring replacement cost guide, repair cost guide, and why garage door estimates are so different.
How Advanced Door Helps When Your Garage Door Slams Shut
When you call us about a garage door that slams shut, here is what to expect:
- A clear diagnosis. We check the springs, cables, drums, bottom brackets, opener, and settings, and tell you exactly what we found.
- Honest options. If it is the bottom seal, we tell you. If it is the springs, we explain why and what we recommend.
- The right parts. Springs are matched to your door’s weight and size, and replaced in pairs on two-spring doors.
- A balanced door. We balance the door, reset the opener’s force and travel limits, and test the safety reverse before we leave.
- Help when it cannot wait. If your door is stuck open or unsafe, see our emergency repair guide and give us a call.
We serve homeowners and businesses across Utah, including Ogden, Draper, Logan and Cache Valley, Layton and Davis County, Sandy, Provo and Utah County, Lehi, St. George, and Park City.
Call (844) 971-3667 any time, or reach a local team directly: Ogden (801) 430-9021, Logan (435) 363-4929, Draper (801) 967-8998.
Related reading: garage door troubleshooting guide, garage door jerking or moving unevenly, garage door closes then reopens, and why your garage door will not close.
Frequently Asked Questions: Garage Door Slams Shut
Why does my garage door slam shut?
The most common reason is a spring problem. A broken, worn, or wrong-size spring leaves the door heavier than the system is set up for, so it speeds up and hits the floor hard. Broken or frayed cables, a disconnected opener, opener wear, and a door that has gotten heavier can also cause it. A worn bottom seal can make a normal close sound like a slam.
Is it safe to use a garage door that slams shut?
No. A door that slams is not being held by its springs the way it should be, and it can fall faster than the safety sensors and auto-reverse are designed to handle. Stop using it, unplug the opener, keep people and pets clear, and have a technician inspect it.
Why does my garage door close too fast at the bottom?
A door that speeds up over the last few feet usually has weak or worn springs, or springs that were not sized correctly for the door. Near the bottom, spring tension is lowest, so any loss of spring force shows up most at the end of travel.
Can a broken spring make a garage door slam shut?
Yes. A broken torsion spring is the number one cause. On a one-spring door, a break leaves the door with almost no counterbalance. On a two-spring door, the remaining spring is overloaded. Either way, the door will be heavy and can drop or slam.
Why did my garage door fall when I pulled the emergency release?
When the opener is connected, it can hide a balance problem by controlling the door’s speed. When you disconnect it, an unbalanced door falls on its own. That usually means weak or broken springs. Never pull the release with the door open unless you know the springs and cables are good.
Can I adjust the springs myself to stop the slamming?
We do not recommend it. Springs, cables, and bottom brackets are under high tension, and adjusting them requires special tools and training. DASMA advises that spring systems be repaired only by trained professionals.
Will turning up the opener force fix a door that slams?
No. Force settings control how hard the opener pushes, not how much weight the springs carry. Turning up the force can make the auto-reverse less sensitive and wear out the opener faster. Fix the balance first, then reset the force and travel limits.
How do I know if it is the springs or just the bottom seal?
Watch the speed. If the door moves at a steady pace the whole way and only the final contact is loud, the bottom seal or floor is a likely cause. If the door speeds up, drops, or closes crooked before it touches, check the springs and cables first and have a technician inspect it.
Reference: DASMA, Garage Door Safety Tips (springs and cables under high tension, replace both springs, safety cables for extension springs, bottom brackets for trained technicians only, out-of-balance doors, and annual professional service).
Get a Free Estimate from Advanced Door
Garage door slamming shut? We will find the cause, fix it right, and balance the door safely.
Serving Ogden, Salt Lake City, Provo, Park City, Logan, and all of Utah
Call for a free estimate. No pressure, no hidden fees.
Current offers: $100 off any new door or 10% off any service call
(Offers cannot be combined)
